Skip to content

Resin Driveways

Resin Bound Driveway Installation in Huntingdon

A trowelled resin surface that drains properly, holds its finish, and starts with the right base assessment.

  • Itemised Quote
  • Base Assessment First
  • SuDS Compliant
A large detached brick house with a new light-coloured resin-bound driveway, lush green lawn, and colourful landscaped garden.

What Goes Wrong

Why some resin driveways crack or puddle within a few winters

The finish is only as good as what sits beneath it. These are the failure modes that a proper survey and preparation prevent.

Skipped Base Check

Laying resin over a failing or uneven base traps the problem underneath, and cracks appear at the surface within one or two winters.

Ground Condition Survey

A site survey assesses stability, drainage fall, and whether the existing surface can carry an overlay before any work is quoted.

Overlay on Bad Concrete

Older Huntingdon driveways often have cracked or hollow concrete that moves seasonally. Resin bonded over it will mirror every crack.

Excavation When Needed

Where the base is unsound, the old surface is removed and a compacted MOT Type 1 sub-base is laid to the correct depth for the ground.

Poor Drainage Fall

Without a checked drainage fall, water pools at the house wall or sits on the surface, softening the resin layer over time.

Drainage Checked at Survey

Fall direction and channel positioning are confirmed before the resin is applied, so water clears the surface towards a boundary or drain.

No Edge Restraints

Resin laid without fixed edge restraints spreads and crumbles at the perimeter, leaving a ragged line that widens with each frost cycle.

Restraints Before Resin

Edge restraints are installed and set before the resin layer goes down, holding the material at the perimeter and defining the finished line.

Installation Process

From bare ground to finished resin surface: what each stage involves

Getting the sub-base and drainage right at the start is what separates a surface that lasts from one that cracks within two winters.

Request a Survey

The process starts with a site survey covering base condition, existing drainage fall, and ground stability. Huntingdon properties often have older concrete or tarmac that needs assessing before an overlay is possible. Where the existing base is sound, preparation involves cleaning, crack repair, and priming. Where it is not, excavation removes the old surface and a compacted MOT Type 1 sub-base is laid to the correct depth for the ground conditions.

Aggregate is selected at survey stage from physical samples, allowing colour and stone size to be matched against the property’s brickwork or boundary materials. The resin binder and aggregate are mixed together, then hand-trowelled to a consistent finish across the surface. Edge restraints are installed before the resin layer to hold the material at the perimeter and define the finished line.

Drainage fall is checked before the resin is applied, water needs to clear the surface towards a channel or boundary, not pool at the base of the house. On new Cambridgeshire builds, drainage patterns are assessed as part of the survey. Cure time before vehicle use is typically 24 hours in dry conditions. The permeable structure of a resin bound surface means it meets SuDS rules, removing the need for planning permission on most front driveways.

Why Choose Us

Why choose us for resin bound installation in Huntingdon?

We take your enquiry and manage the quote process so every stage is accounted for before work begins.

Itemised Quotation, Every Time

Excavation, sub-base, drainage, and resin finish are quoted as separate line items, not one combined figure.

Surveyed First, Written Quote

We take your enquiry and schedule a survey across Huntingdon and the surrounding Cambridgeshire area.

Survey Before Any Commitment

A ground condition survey is arranged before a price is agreed, so the quote reflects actual site conditions.

SuDS Compliance Covered

The survey includes a check on whether the installation meets SuDS rules, avoiding planning permission issues on front driveways.

Aggregate Selection at Survey

Colour and stone size are chosen from physical samples at survey stage, matched to the property’s existing materials.

A completed resin driveways job at a house
A finished resin driveways project

How It Works

From first enquiry to finished driveway in three steps

Request a Survey

  1. 01

    Tell Us About Your Drive

    Describe the area, what surface is down now, and how it currently drains, this shapes the survey.

  2. 02

    Survey & Itemised Quote

    The survey assesses the base, checks drainage fall, and quotes excavation, sub-base, and resin finish separately.

  3. 03

    Installation & Cure

    Work runs from base preparation through to trowelled resin finish, with the surface ready for vehicles within 24 hours.

Pricing Estimates

Typical Resin Bound Driveway Installation Prices

JobTypical cost
Overlay on existing driveway£60-£80 per m²
Full installation with sub-base£120-£160 per m²
Small driveway installation£1,800-£3,500
Typical two-car driveway installation£3,500-£5,500
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about resin bound installation in Huntingdon

  • Can my existing driveway be used for resin bound, or will it need digging out?

    It depends on the condition and type of your existing surface. A sound, stable tarmac or concrete base in good condition can often be overlaid directly. If there is movement, cracking, or a weak sub-base, excavation will be needed first. A site assessment confirms which route applies to your driveway.

  • How do I know if the base underneath my old driveway is good enough?

    The base needs to be rigid, level, and free from movement before resin goes down. Signs of a failing base include cracking that follows a pattern, areas that flex underfoot, or visible dips. A physical inspection checks depth, compaction, and drainage capacity before any work is quoted.

  • Will it drain properly on my site, or will water pool?

    Resin bound is fully permeable, so water passes through the surface itself rather than running off. Whether it drains well overall depends on what sits beneath it. If the sub-base and ground below are also permeable, pooling is unlikely. Where the ground is clay-heavy or impermeable, a drainage channel or suitable sub-base design is needed.

  • How much groundwork is usually needed before the resin goes down?

    It varies by site. An overlay on a sound existing surface needs minimal groundwork, cleaning, edge restraints, and minor repairs. A full installation from scratch involves excavation, a compacted MOT Type 3 or open-graded sub-base, and edging before the resin layer. We quote excavation, sub-base, drainage, and resin finish as separate lines so you can see exactly what each stage costs.

  • Is a full dig out always needed, or can you work over what is already there?

    A full dig out is not always necessary. A stable, well-drained existing surface can be overlaid, which saves time and cost. If the base is compromised, a dig out is the only way to guarantee the finished surface will not fail. The site assessment determines which approach is appropriate. Learn more about resin overlays

  • How does resin bound compare with block paving, tarmac, or plain concrete?

    Block paving can shift and weed between joints; tarmac and plain concrete are impermeable and can generate surface run-off. Resin bound is a single poured layer with no joints, passes SUDS drainage requirements, and does not require planning permission on most residential driveways. It also offers a wider choice of stone colours and finishes than any of the three alternatives.

  • Will it be suitable for cars and everyday use on my driveway?

    Yes. A correctly installed resin bound surface handles standard domestic vehicle loads without issue. The key factor is sub-base depth and compaction, a well-prepared base distributes load and prevents the surface cracking under repeated use. It is not suitable for HGV traffic without a specifically engineered sub-base.

  • How do I know the finish will last if the preparation is not done properly?

    Poor preparation is the single most common cause of resin bound failure. If the base moves, the surface cracks; if drainage is wrong, water undermines the bond. We quote excavation, sub-base, drainage, and resin finish as separate line items so every stage is specified and visible, not bundled into a single figure that hides shortcuts.

  • Which areas do you cover for Resin Bound Driveway Installation?

    We cover Resin Bound Driveway Installation in and around Huntingdon, including Godmanchester, St Ives, Brampton, Alconbury Weald, Sawtry, Ramsey, Buckden, Kimbolton and Hemingford Grey. If your area isn’t listed, send us a quick message to check.

Tell Us About Your Driveway

Describe the area, what is down there now, and how it drains. We’ll schedule a base assessment and quote every stage separately.

Request a Survey